Видео

Do these issues apply to the zd30 engine when installed in the Navara D22?

Hi, Do youknow how to reset the fan? Is there a reset button on the fan itself? Ive tried and this is the only smart device in my house that wont connect anymore.

Im just trying one on my bike , had no idea how to fit it until i watched videos like yours. It was a little trickier with heated grips, i like the fact i can let go of throttle now and dont risk getting hit from behind because bike slows down fast when you you let go. Great vid mate.

Mine keeps going into low voltage. It’s plugged into 12v. Any ideas how to fix this?

Great video thank you

Perfect! I've always been skittish of "mechanical" type stuff and this was super easy.

Not sure how these can be called ebay batteries, brick and mortar stores sell them. AMX for example

I haven't watched this yet but thought I'd share my experience. i get a tadd under 24hrs in my car running on an 80ah AGM battery before the built in medium cut off switch kicks in, which I believe is around 10.5 amps compressor running. 60th anniversary 40l. Brand new battery. I'd let it go lower but Engel's lowest cutoff I believe is far too low for AGM

hi , great vid , just wondering have u ever heard of the controller settings access fail , ? i cannot get into the settings to adjust fuel/hrz rpm etc , maybe this is a cheap generic controller (comes with heater) that hasn't got that feature > thanks ( mine has a cog symbol not wrench) cheers

When you roll out throttle, does it disengage like you pressed the disengage button?

Thanks, my welder is now fixed. large aluminum ground wire and stud rotted off. large mouse nest inside.

Hey mate how uncomfortable is that seat on the bike I got one on my fatboy lol

😀 😃

the key was finding the slot to stick the phillips head in, worked like a charm....thanks

Good job

The hard reset screen does not appear on mine.

hi thank you for the great video. I was hoping you could answer some questions. Do you use curing salts specifically cure #2? Do you control the humidity in your tent at all? How fast do you have the fan going? I wan to try curing some sausage in a refrigerator and I was just going to put a battery operated fan inside. and right now I am in the research and information gathering stage before I dive in. Thank you for your reply.

I’ve done exactly that and it wont connect, have a few grid connect items so familiar with pairing, know of how to reset the ceiling fan? Ive created a new account so thinking that may be part of the cause

Over the last couple of years I have changed every bush in the front end along with tie rod ends. Also hub rebuild when I first got my 97 GQ . New all terrains and rims. Still wobbles at 90 to 100. Only thing I haven't done is remove the shims. There is a preload of .5 to 1.5kg on the swivel hub from memory.

Greetings from Cape Canaveral! I just purchased Scram 411 and this is exactly the kind of info I’m looking to find out. Florida is very flat and hot. I got the Scram because I felt that like it was a grown up version of a trail 90 or a TW that could keep up in traffic when necessary. The bike has no problem in traffic but I’ve felt like is was wound up pretty good. I’m planning on this mod but wasn’t sure what size tooth sprocket to use. Good video! Please keep them coming!

Great video! - before I start - the pocket/vents above the stereo, you didn't show these being removed? Do they just come out with the dash and you just swap over or are they connected to the sub frame? Cheers!!

great tips mate. I'm in Sweden and will be dusting off teh 50hP 1981 Johnsson next week and these tips will be great for looking into some problems i had at the end of last season.

Do away with the tailshaft centre bearing all together by having 1 piece tailshaft instead

Good to see there's still potential candidates for a Darwin Award out there. Ignore multiple warnings in the manual about placing the tip in coals - check! Circumvent the rocker switch safety - check! No less than 8 highlighted warnings in the manual but "it doesn't really tell you anything you need to know" - check! Still, thanks for the review. I think I'll definitely get one, but I'll follow the instructions and use the safety switch as intended . Cheers.

Thank you very much!

Doesn't work when you got the auto switch at the end.....

once you have the auto part out. should the rest of the locker inside the hub still spin. not sure if my entire assembly is cooked.

Mine is doing the same goes down but not up switch the relays and it’s still only going down any ideas it’s a 70 Johnson 2000

how do you select Alpine mode? I know it can be done with this controller have forgotten the procedure.

My US spec 2006 was slightly different than this, but close enough to get me there, thanks! Hardest part was disonnecting some of the electrical where the latches were hidden or not obvious. The one with the spring wire clip lock was particularly puzzling until I realized you just gotta pry the wire out. There's actually two but the one on the MAP I just pulled the sensor and replaced that -ring while I was at it.

Thank you

Link

Thank you for taking the time to do this.

Thanks so much for the clear instructions

Thanks for the simple and quick video. It helped me change the blade on my Worx edger. Exact same process.

This video made me feel far more confident digging into my MIG welder and fixing it myself (no arc issue). Thank you for making it!

Good video tnx

We need people like you to review these products to keep them honest.

Dose that fit for gsxr1000r

Hi. Can you use raw garlic, not powder?

Excellent! Thanks so much for posting.

That was a perfect video. Thank you.

I have a Sunnyboy or Solarbridge that is displaying an ERR 0P-0013-10. Do you have any idea of what this might be or where I can learn more? I will try to attach a picture of the message.

Thanks! Saves me a whole lot of time trying to work out what battery we needed for ours!

🇱🇰🙏❤

Mine is 98 montero/Pajero Gen 2.5 Same process?? Cheers from Florida!! 🤙🏼🍺

I like it! I've used a cordless vacuum but this looks way better!

Very helpful video, so firstly thank you. I think my timer must be set, but didn't set it. I have only just installed the unit it's like yours in the video but I've had it for nearly 3 years. I never set the timer but I walked out to the van this morning and it was going but it wasn't warm, how do I turn it off the timer please mate, and why would it not be hot, does it need to be primed before start every time? Thank you

Hey mate this was awesome , where in Oz are you ? I’m in Brisbane have Gen4 (NT ) would like a front locker … happy to pay by the hour

What do you mean by “stand alone”?